Arlington (Main Office)
Boost Air And PlumbingArlington, TX
- 2313 Michigan Ct
Arlington, TX 76016 - (817) 839-4672
- Mon–Fri: 8:00 AM – 6:00 PMSaturday: 9:00 AM – 6:00 PMSunday: Closed
Mechanical
Rooftop Unit Installation in Arlington & Grand Prairie, TX
We provide heavy-duty rooftop unit installation for businesses facing failed compressors or inefficient cooling. Our NATE-certified technicians handle the crane logistics, curb adapters, and high-voltage wiring required to get your facility back to a comfortable temperature quickly.
What neighbors say
What Our Customers Are Saying
Selecting the Right RTU for Your Square Footage
Choosing a rooftop unit is not as simple as matching the tonnage of the old machine. Modern units from brands like Carrier and Lennox often have different footprints than older models. We measure your existing curb and airflow requirements to determine if we need a curb adapter or a full replacement. We also calculate the heat load based on your building materials and occupancy levels.
An oversized unit will short-cycle and fail to remove humidity. This is a common problem in North Texas where humidity levels spike in the morning. A correctly sized system stays on long enough to pull moisture out of the air. This protects your inventory and keeps your employees comfortable. Our technicians focus on long-term reliability over a quick sale.
Crane Logistics and Site Safety Planning
Rooftop installations require precision during the lift. We manage the crane schedule and ensure the work area is blocked off for safety. Our team inspects the structural integrity of the roof before the new unit is lowered into place. We minimize the time your building is open to the elements. Efficiency is our main priority during the lift.
Safety is not negotiable on a commercial job site. We follow strict OSHA guidelines and EPA 608 standards for refrigerant handling. If we are performing a Commercial HVAC Installation at a retail center, we work around your peak hours to avoid disrupting customers. We get the heavy lifting done and the unit powered up as fast as possible.
Integrating Exhaust Systems and Economizers
Most commercial RTUs work alongside other mechanical components. We often perform Exhaust Fan Installation at the same time we swap the main unit to ensure proper building pressure. If your exhaust fans are pulling too much air, your new RTU will work harder than it needs to. We balance the air so your doors do not slam or whistle.
We also specialize in economizer setup. These components pull in outside air when the temperature drops, saving you money on electricity. In DFW, the shoulder seasons offer great opportunities for free cooling. We verify your dampers are calibrated and the sensors are communicating with your Honeywell or ecobee thermostat correctly. High-efficiency setups require this level of detail.
Commercial HVAC Maintenance and Compliance
Once the new unit is bolted down and wired, our work continues with a full system test. We check the gas pressure, voltage draw, and refrigerant charge. We document every reading to ensure it meets manufacturer specifications for warranty coverage. A bad startup is the leading cause of premature RTU failure. We do not skip these steps.
Whether you have a small retail shop or a large facility with Chiller Installation needs, we treat every job with the same technical rigor. We have seen what the Texas sun does to unprotected components. We use high-quality sealants and weatherproofing to protect your investment for years. For dependable Commercial HVAC Repair and installation, we are the local choice.
What you get
- Precise curb mounting to prevent leaks and structural vibration issues.
- Manual J load calculations ensuring your unit handles Texas heat.
- Rigid duct connections sealed with high-grade mastic for efficiency.
- Crane coordination and site safety managed by our NATE-certified techs.
- Full compliance with all local Arlington, Grand Prairie, and DFW mechanical and electrical codes.
How it works
- 1We perform a load calculation to size the new Trane or Carrier unit.
- 2Our team coordinates the crane rental and safety perimeter for the swap.
- 3We secure the unit to the roof curb and seal all transitions.
- 4The system is commissioned with a multi-point startup and airflow test.
Related services
Why call us
- • 10+ years in DFW
- • TDLR / TSBPE licensed
- • Flat-rate, written pricing
- • Same-day weekday service
- • Financing on qualifying jobs
FAQs
Frequently asked questions
Need Rooftop Unit Installation in Arlington or Grand Prairie Today?
Call Boost Air And Plumbing at (817) 839-4672 for a professional site assessment.
ServingArlington HVACandGrand Prairie HVACwith same-day dispatch.