Limited-time financing: 0% APR for 24 months on new HVAC system installs.Claim now
Boost Air And Plumbing logo, HVAC and plumbing in Arlington, TXBoost Air And Plumbing
Boost Air And Plumbing service van on a residential job in North Texas

Boost Air Blog

Plumbing Leak Repair in Irving, TX: Finding and Fixing Leaks

Need plumbing leak repair in Irving? Call (817) 612-9107 or Book Online

Part of our Leak Detection guide.

Quick answer

Plumbing leak repair in Irving starts with the signs: a high water bill, a meter that moves with everything off, damp spots, a musty smell, warped floors, low pressure, or the sound of running water. Shut off the main water valve if water is actively leaking. A technician confirms the leak with a pressure test and acoustic or thermal detection, then the repair is a spot repair, a reroute, or a repipe.

Plumbing leak repair in Irving is a find-it-first job. The stain on the ceiling is often not the break. Water runs along a joist, a wall, or the underside of a slab, and it shows up somewhere easier. Leak detection is how the break gets marked. Plumbing in Irving is the local page. Trucks come from the Arlington and Grand Prairie shops. There is no Irving shop.

If water is running where it should not, shut the main off before you read the rest. The steps are in the next section. Then book the visit. A leak that is still fed will not stay the size you found.

Signs you have a leak

You do not need a puddle to have a leak. These are the signs that are worth a test:

  • A high water bill. One hot month of irrigation can explain a bill. A bill that jumped while the yard was off, or that stayed high after you changed nothing, is a reason to watch the meter.
  • The meter moves with everything off. Close every faucet. Pause the irrigation. Wait until the ice maker and any under-sink filter are quiet. Then watch the meter for a few minutes. A digital meter may show a flow mark, or the digits may tick. An older meter has a small triangle or a sweep hand. If that moves while nobody is using water, water is leaving the system.
  • Damp spots. A new stain on a ceiling, a dark patch of carpet, or a place on a hardwood floor that will not dry. The break can be several feet away from the stain, because water follows the easy path.
  • Mold or a musty smell. A closed room that smells wet, or mold low on a wall, can be a slow leak rather than a humidity problem. Smell alone is not proof. Smell plus a moving meter is.
  • Warped floors. Wood that cups, or tile that sounds hollow and starts to loosen, has been wet for a while. That is past the "wait and see" stage.
  • Low pressure. A house that used to have normal pressure and now does not, at more than one faucet, can be losing water. One faucet with a clogged aerator is not a slab leak. Whole-house pressure that fell is a reason to test.
  • The sound of running water. A hiss or a trickle inside a wall, or under the floor, when every fixture is off. If you can hear it, shut the main and then look.

A puddle that is only under the water heater is a heater leak, not a line under the slab. This page stays on the piping.

Shut off the main during an active leak

Do this while water is still coming out. Find the house shutoff. It is often where the line enters the house, or on the house side of the meter.

  • A lever handle is open when the lever is in line with the pipe. Turn it a quarter turn so the lever sits across the pipe.
  • A round handle turns clockwise until it stops. Do not force a handle that will not move. A broken valve is a bigger leak.

Open a faucet at the lowest sink after the valve is closed so the pipes drain down and the leak slows. If the shutoff will not turn, keep people off the wet floor and book the visit now. Call (817) 612-9107 or book online. Same-day plumbing visits are available Monday through Friday. Hours are Monday through Saturday, 8am to 7pm.

If you smell gas while you are at the meter or the heater, leave the house. Do not flip switches. Call the gas company or 911 from outside.

Slab leaks under North Texas foundations

A lot of Irving houses are on a concrete slab, with the hot and cold lines under that concrete. The clay soil under those slabs swells when it rains and shrinks in a dry summer. The slab moves. A copper line in that movement can rub, kink, or open a pinhole. The water then leaves under the house.

That is a slab leak. It often shows up as a warm streak in the floor when the hot line is the one that failed, a damp spot in the carpet, or the meter test above. It does not show up as a drip you can tighten with a wrench. Leaving it fed washes soil out from under the slab. Shut the main, and have the line found before anyone opens the concrete.

How the leak is found

The damp spot is a clue. It is not the mark for a jackhammer. Leak detection is the step that narrows the break before the repair opens anything.

  • Pressure test. A section of pipe is isolated and a gauge watches it. If the pressure falls and no fixture is open, that section is losing water. The test says the leak is real, and it says which part of the system it is in.
  • Acoustic detection. Listening gear follows the sound of water leaving a pipe that is still under pressure. The sound is loudest near the break. That is how a pinhole under a slab gets a mark instead of a guess.
  • Thermal detection. A hot-water leak warms the concrete above it. A cold leak can cool it. A scan of the floor looks for that temperature change and traces it back toward the line. It is more useful on a hot line than on a cold one, so it is used with the pressure test, not instead of it.

The result you should see is a marked spot and an explanation of which line it is. The repair quote comes after that, not before.

Spot repair, reroute, or repipe

The repair follows the rest of the pipe, not only the hole that was found. Pipe repair is the service for that fix. The final price depends on which option the house needs, and on access. This page does not quote a dollar figure.

Spot repair. One confirmed break, and the pipe on either side is still sound. The opening is the smallest area that reaches the break. The line is repaired and tested again. This is the right scope when the rest of the system is not failing with it.

Reroute. The break is under the slab, and opening the floor is the worse option, or you do not want to cut that slab again for the next pinhole on the same line. A new line is run through the attic or the walls, and the failed section is taken out of service. The fixtures come back on the new path.

Repipe. The leak is not the only weak pipe. Galvanized lines that are rusted down inside, or several leaks across the same system, mean the next leak is already forming. Repiping replaces the supply piping instead of chasing one hole at a time. A single pinhole in otherwise sound copper is not a reason to repipe the house. Several leaks, or pipe that is already thin, is.

Ask the quote to name which of the three it is, which line, and what gets opened. A price with none of that is not a finished scope. The service fee is $0 when you approve the repair.

Book it while the water is off

An active leak does not get better because the floor dried for an hour. Shut the main, note what you saw (the meter, the room, hot or cold), and book the visit the same day. Call (817) 612-9107 or book online. Say it is a leak, and say whether the main is already off. Same-day service is available Monday through Friday. Hours are Monday through Saturday, 8am to 7pm.

Frequently asked questions

What are the signs of a plumbing leak in an Irving house?
A water bill that jumped, a meter that keeps moving with every fixture off, damp spots, a musty smell or mold, warped floors, pressure that dropped, or the sound of running water when nothing is on. One warm spot on a slab floor is a reason to test, not a reason to open the concrete yet.
What should I do if water is leaking right now?
Shut off the main water valve. A lever handle turns a quarter turn so it sits across the pipe. A round handle turns clockwise until it stops. Then open a faucet so the pressure drops. If you smell gas, leave and call the gas company from outside. Call (817) 612-9107 or book online after the water is off. Hours are Monday through Saturday, 8am to 7pm, with same-day visits Monday through Friday.
What is a slab leak?
It is a leak in the water line under the concrete foundation. Irving houses on North Texas clay see this when the soil swells and shrinks and the slab moves against the pipe. The water shows up as a warm or damp floor, a moving meter, or both, not as a drip under a sink.
How does a technician find the leak?
A pressure test shows whether a section of pipe holds. Acoustic listening follows the sound of water leaving a pressurized line. Thermal detection looks for a warm or cool spot on the floor, which is more useful on a hot-water leak. The point is to mark the break before the floor or the wall is opened.
Is the fix a spot repair, a reroute, or a repipe?
A spot repair fits one break in pipe that is otherwise sound. A reroute runs a new line through the attic or the walls and abandons a failed section under the slab. A repipe replaces the supply system when the rest of the pipe is in the same condition. The final price depends on which of those the house needs.

Need a hand from a licensed tech?

Call (817) 612-9107 or book online. We serve Arlington, Grand Prairie, and the surrounding North Texas communities.

Visit our shops

Two DFW locations serving the entire Metroplex

Boost Air And Plumbing dispatches trucks from our Arlington main office and our Grand Prairie shop, covering Tarrant and Dallas counties with same-day HVAC and plumbing service. Call (817) 612-9107 for either location.

Arlington (Main Office)

Boost Air And PlumbingArlington, TX

  • 2313 Michigan Ct
    Arlington, TX 76016
  • (817) 612-9107
  • Monday to Saturday: 8:00 AM to 7:00 PM
Get directions

Grand Prairie

Boost Air And PlumbingGrand Prairie, TX

  • 2100 TX-360 Ste 907
    Grand Prairie, TX 75050
  • (817) 612-9107
  • Monday to Saturday: 8:00 AM to 7:00 PM
Get directions