Limited-time financing: 0% APR for 24 months on new HVAC system installs.Claim now
Boost Air And Plumbing logo, HVAC and plumbing in Arlington, TXBoost Air And Plumbing
Boost Air technician performing a furnace repair on a residential unit

Boost Air Blog

An Attic Furnace That Will Not Heat in Grand Prairie, TX

Attic furnace will not heat? Call (817) 612-9107 or Book Online

Part of our Furnace Repair guide.

Quick answer

An attic furnace in Grand Prairie often fails on the first cold night after months of cooling, or because a float switch from the summer drain is still open. Check the thermostat, the filter, and one breaker reset. Do not open the burners in the attic. Boost Air repairs gas furnaces. Approved repairs include a $0 service fee. Same-day service is Monday through Friday.

Grand Prairie attic furnaces spend summer as a stand for the cooling coil. The gas heat may not run from April to November. The first cold night is the first test of the igniter, the flame sensor, and the inducer, and it is also when a float switch left over from an August condensate clog can still be open. No heat in that house is often a cooling-season leftover plus a part that sat still.

Boost Air And Plumbing repairs gas furnaces. We do not service boilers. Furnace repair is the service. HVAC service in Grand Prairie is the local page.

Smell gas and leave. Call the gas utility or 911 from outside. If a carbon monoxide alarm sounds, everyone out, then 911. Do not climb into the attic to investigate either one.

A ten-minute check that stays out of the attic

Do this from the hallway and the yard.

  1. Thermostat on Heat, not Emergency, fan on AUTO, setpoint a few degrees above the room. Emergency heat on a heat pump is a different system. A gas furnace does not need that switch.
  2. Filter. If you cannot see light through it, replace it with the size on the frame. A packed filter opens a limit. The burners stop and the blower may keep running.
  3. Breaker, once. A second trip stays off. If the switch at the attic stairs was off for a filter change, turn it back on and seat the panel. An open blower door is a switch.
  4. The outdoor end of the condensate PVC, if you can reach it. Slime in that line is how the float opened in the summer. Clearing the end you can see is reasonable. A pan of water over wiring is not a flashlight project at night.

Wait one cycle. If it lights and stays lit, you are done. If it clicks and quits, stop resetting it.

What the attic visit is for

We confirm the thermostat is calling, the door switch is closed, and a float is not the thing holding the gas valve off. Then the startup order: inducer, ignition, flame proof, blower. A sensor that lets the burners light and then drop out is a different part from an igniter that never glows. You should not have to guess which one from the hallway. We say which step stopped, and the price, before parts go in.

Approved repairs include a $0 service fee. Same-day service is Monday through Friday.

A limit that opens again after a new filter can be a duct problem, a dirty blower, or a furnace that is overheating for a worse reason. Repeated overheating is not fixed by bypassing the switch. Soot or a yellow flame means the furnace stays off. That can be a heat exchanger conversation and a free replacement estimate rather than another sensor.

Hours are Monday through Saturday, 8am to 7pm. Call (817) 612-9107 or book online.

Frequently asked questions

Why would a Grand Prairie attic furnace fail on the first cold night? It sat through a long cooling season. The igniter, flame sensor, and inducer may not have run since spring. A float switch that protected the attic from a summer condensate clog can also hold the system off. The symptom is no heat. The cause may be leftover from cooling.

What is safe to check at the thermostat and the filter? Set Heat, fan AUTO, and a setpoint above the room. Replace a filter you cannot see through, and make sure the attic access panel or blower door is seated if you already had it open for the filter. Reset a breaker once. Do not go into the attic at night to open the burner compartment.

Can last summer's drain clog stop the heat? Yes. A float switch in the attic pan opens when water is high. It can break the call for heat the same way it broke the call for cooling in August. Clear a visible clog at the outdoor end of the PVC if you can reach it from the ground. If the pan is full near wiring, leave it.

When should I stop resetting it? After one or two tries, or immediately if you smell gas, hear a rollout, see soot, or the same code returns. Gas smell or a carbon monoxide alarm means leave and call from outside.

When is no heat a replacement quote? When the heat exchanger is cracked, the cabinet is rusted through, or a major part failed on a furnace around 15 years old. A sensor or igniter on a sound exchanger is often a repair. Approved repairs include a $0 service fee. Ask for a free replacement estimate if the numbers are close.

Need a hand from a licensed tech?

Call (817) 612-9107 or book online. We serve Arlington, Grand Prairie, and the surrounding North Texas communities.

Visit our shops

Two DFW locations serving the entire Metroplex

Boost Air And Plumbing dispatches trucks from our Arlington main office and our Grand Prairie shop, covering Tarrant and Dallas counties with same-day HVAC and plumbing service. Call (817) 612-9107 for either location.

Arlington (Main Office)

Boost Air And PlumbingArlington, TX

  • 2313 Michigan Ct
    Arlington, TX 76016
  • (817) 612-9107
  • Monday to Saturday: 8:00 AM to 7:00 PM
Get directions

Grand Prairie

Boost Air And PlumbingGrand Prairie, TX

  • 2100 TX-360 Ste 907
    Grand Prairie, TX 75050
  • (817) 612-9107
  • Monday to Saturday: 8:00 AM to 7:00 PM
Get directions